Supply Voltage VDC 0 to 16 V
Supply Voltage VDD 0 to 16 V
Logic Input Voltage -0.5 to 20 V
Logic Output Voltage -0.5 to 15 + 0.5 V
Max. SOx Current 20 mA
Gate Peak Current Iout -30 to 30 A
Min. Gate Resistance 1 O
Max. IGBT Gate Charge t.b.d. µC
Max. Average Supply Current IDC 540 mA
Max. Output Power at Ambient Temperature less than 70 ºC 4 W
Max. Output Power at Ambient Temperature 85 ºC t.b.d. W
Max. Switching Frequency F 60 kHz
Max. Operating Voltage 1700 Vpeak
dV/dt t.b.d. kV/µs
Operating Temperature -40 to 85 ºC
Storage Temperature -40 to 90 ºC
Nominal Supply Voltage VDC 14.5 to 15.5 (typ. 15) V
Nominal Supply Voltage VDD 14.5 to 15.5 (typ. 15) V
Input Logic Level of InX – Turn-On Condition 15 V
Input Logic Level of InX – Turn-Off Condition 0 V
Supply Current IDC 65 mA
Supply Current IDD at F = 0 Hz 16 mA
Supply Current IDD at F = 60 kHz 24 mA
Coupling Capacitance Cio t.b.d. pF
Supply Threshold VthC Primary Side 11.9 to 13.3 (typ. 12.6) V
Supply Threshold VthS Primary Side 11.3 to 12.7 (typ. 12.0) V
Min. Monitoring Hysteresis Primary Side 0.35 V
Supply Threshold VthC Secondary Side t.b.d. V
Supply Threshold VthS Secondary Side t.b.d. V
Monitoring Hysteresis Secondary Side t.b.d. V
Input Impedance 3.9 kO
Max. SOx Output Voltage 0.7 V
Blocking Time 31 ms
Threshold Level 5 V
Turn-On Delay td(on) 400 ns
Turn-Off Delay td(off) 600 ns
Short Pulse Suppression 200 ns
Dead Time between Channels 1.1 µs
Transmission Delay of Fault State 500 ns
Turn-On Voltage 15.0 V
Turn-Off Voltage -15 V
Max. Test Voltage at 50 Hz/1 min 4000 Veff
Min. Partial Discharge Extinction Voltage 1700 Vpeak
Min. Creepage Distance Primary to Secondary Side I. 15 mm
Min. Creepage Distance Secondary to Secondary Side I. 16 mm
Min. Creepage Distance Primary to Secondary Side II. 15 mm
Min. Creepage Distance Secondary to Secondary Side II. 6.2 mm
Absolute Maximum Ratings VDC to GND VDD to GND InA, InB and Mod to GND SOI and S02 to GND Failure condition, total current Turn-on and turn-off Primary and secondary to secondary side Rate of change of input to output voltage
Recommended Operating Conditions VDC to GND, IGBT mode 2 VDD to GND
Electrical Characteristics Power Supply (All data refer to +25 °C and VDC = VDD = 15 V unless otherwise specified) without load Primary to output, per channel
Power Supply Monitoring Clear fault Set fault Set/clear fault
Logic Inputs and Outputs V (In) = 15 V 2 Failure condition, I (SOx) < 20 mA
External Fault Input between E.X and COM X
Timing Characteristics Direct mode Half-bridge mode, without additional CA/CB
Output Voltage Gate X to COM X
Electrical Insulation IEC60270
Product Highlights Dual channel driver Highly integrated SCALE-2 chipset Switching frequency up to 60 kHz Gate current ±30 A 4 W output power per channel Direct and half-bridge mode IGBT short-circuit protection Failure soft shut down Isolated DC/DC converter Safe isolation to EN 50178 Reliable, long service life
Applications 1:1 replacement of 2ED300C17-S IGBTs up to 1700 V
Safety Notice The data contained in this data sheet is intended exclusively for technically trained staff. Handling all high- voltage equipment involves risk to life. Strict compliance with the respective safety regulations is mandatory! Any handling of electronic devices is subject to the general specifications for protecting electrostatic-sensitive devices according to international standard IEC 60747-1, Chapter IX or European standard EN 100015 (i.e. the workplace, tools, etc. must comply with these stand
  • The SCALE-2 dual-driver core 2SD300C17 is a second source to Infineon's 2ED300C17-S. The driver is fully pin and function-compatible to the 2ED300C17-S and was designed for applications in which high reliability is expected.
  • The use of CONCEPT'S highly integrated SCALE-2 chipset allows 6 3% of the components to be dispensed with compared to the 2ED300C17-S. This advantage is impressively reflected in increased reliability (function and MTBF) with simultaneously lower costs.
  • The 2SD300C17 combines a complete two-channel driver core with all components required for driving, such as an isolated DC/DC converter, short-circuit protection, failure soft shut down, short pulse suppression as well as supply voltage monitoring. Each of the two output channels is electrically isolated from the primary side and the other secondary channel.
  • The driver provides a gate voltage swing of ±15 V. An output current of 30A and 4W drive power is available per channel.
  • Its outstanding EMC with a dv/dt strength of more than 50 V/ns allows safe and reliable operation in even the demanding industrial applications.